Propagation

Propagating Dendrobium Orchids from Cane Cuttings

Cane-type dendrobiums can sometimes be propagated from leafless canes cut into sections and kept humid until keikis form. Steps and caveats.

On this page
  1. Which dendrobiums this works for
  2. Which canes to use
  3. Step-by-step
  4. Care while waiting
  5. Potting the new plantlets
  6. Alternative: keikis that form on their own
  7. Troubleshooting

Which dendrobiums this works for

Cane cuttings are mainly used with cane-type dendrobiums, such as the commonly grown nobile types, which have tall, jointed, pseudobulb-like canes. Other dendrobiums grow differently, for instance with thin reed-like stems or small pseudobulbs, and may not respond in the same way. If you are not sure which type you have, check the care information for your specific plant before cutting anything.

The method is not a certain thing. It can produce new plants, but some canes do not sprout, and it is worth treating it as a low-cost experiment using canes you can spare.

Which canes to use

  • Older canes that have finished flowering and may have lost their leaves are the usual candidates. Leafless old canes are often the ones that are not contributing much to the plant.
  • Choose canes that are firm and plump, not soft, shriveled or dark.
  • Look for the nodes, the slightly swollen joints along the cane. New plantlets form at these.

Do not use all your canes. Leave plenty of healthy growth on the mother plant.

Step-by-step

  1. Sterilize your tools. Use rubbing alcohol on a sharp knife or pruners, and sterilize between plants.
  2. Cut the cane at the base. You may be able to remove the entire cane near the base, which is usually done at repotting time, as described in how to divide orchids.
  3. Cut it into sections. Common practice is to cut the cane into pieces with a few nodes each, though lengths vary. Some growers leave the cane whole and lay it flat.
  4. Let the cut ends dry briefly. Dusting with cinnamon or a fungicide is a common precaution against rot.
  5. Place the sections on damp sphagnum moss. Lay them on the surface or partly press them in, so they are in contact with the moss without sitting in water.
  6. Provide warmth and humidity. A clear container or sealed bag with a few ventilation holes helps keep humidity up. Ventilation is important to reduce rot and mold.
  7. Put it in bright, indirect light. Avoid direct sun, which can overheat the container.

Care while waiting

  • Check the moss regularly. It should stay slightly damp but not wet.
  • Open the container now and then for air exchange.
  • Remove any section that turns soft, black or moldy, so rot does not spread.
  • Be patient. New growth can take weeks to months, and some sections will not sprout.

Potting the new plantlets

When a plantlet (a keiki) has developed its own leaves and roots a few inches long, it can be separated and potted. See when and how to remove and pot an orchid keiki for the general process. Use a small pot with fine orchid bark or sphagnum moss and keep the medium lightly moist.

It may take a few years for a new plant to grow large enough to flower.

Alternative: keikis that form on their own

Cane-type dendrobiums sometimes grow keikis on their canes without any cutting, especially on older canes. If that happens, you can leave the keiki on the cane until it has roots. Read orchid keikis for more.

Troubleshooting

  • Cane shrivels: the section may be too dry or too old. Slightly more humidity may help, but do not make it wet.
  • Mold or rot: improve ventilation, remove affected pieces, and use less moisture.
  • Nothing happens: not every cane will sprout. Try a few sections and see.

For an overview of orchid propagation methods, see how to propagate orchids.

The complete guide to propagation

How to Propagate Orchids from Roots and Divisions
Read the guide

Keep exploring

Guides from other topics

All topics →